• New Boats and Gear RSS Feed

      Published on 02-06-2018 11:36 AM
      Article Preview

      Increased manufacturing capacity in Minden (Nevada, USA) and Sri Lanka focuses on 3Di sails output for small boats

      The beginning of 2018 marks a ...
      Published on 02-06-2018 11:28 AM
      Article Preview

      The operators of the first all-electric ferry in Norway are starting to get some good data on the vehicle and it’s nothing short of impressive.

      They claim that the all-electric ferry cuts emission by 95% and costs by 80% compared to fuel-powered counterparts and the results are attracting customers.

      The ferry in question is called “Ampere” and it was put into operation back in May 2015 with the aim ...
      Published on 01-23-2018 09:39 AM
      Article Preview

      Crew watching
      Just “flip the switch” and watch as all systems turn green. Monitor the battery and signal strength in real time. You will be able to tell if anything is wrong at a glance.

      Every second, the phone checks if the beacon is not in the water and if the connection is not lost. ...
      Published on 12-14-2017 09:16 AM
      Article Preview

      Gotta love the enthusiasm for getting the most out of one jetski... ...
      Published on 11-20-2017 11:51 AM
      Article Preview


      (NORTH KINGSTOWN, RI) November 20, 2017 - Alerion Yachts, the luxury daysailing brand renowned for its combination of stunning, traditional lines and modern ...
      Published on 10-30-2017 11:09 AM
      Article Preview

      Two years and more than 135,000 hours of reflection, work and energy have enabled Team Banque Populaire and Armel Le Cléac'h to give birth to the Maxi Banque Populaire IX, a new generation racing multihull. This new Ultim, handy solo, able to be propelled over the water and chiseled for the most beautiful adventures around the globe, touched the water today at 12:20 in Lorient. It was an ambitious and daring challenge two years ago, it is today a jewel of innovation of 14 tons. Those who imagined it tell ...
      Published on 09-10-2017 04:34 PM
      Article Preview

      Lois Lane made her 1st sailing event in quite some time last week,
      entering in the RYC's Wednesday Night Beer Can regatta. Owner Tony Carr has spent the past 5 years putting in a bundle of time and money rehabbing ...
      Published on 08-30-2017 09:29 AM
      Article Preview

      Secret testing going on with the crews at Slingshot!

      An inflatable kite, sans all the messy strings combined with ...
      Published on 08-13-2017 09:49 AM
      Article Preview

      12.08.2017 by Ben Remocker
      Class Update following the Nacra Sailing recall of Foiling Boats

      On Friday August 11, 2017, Nacra Sailing issued a recall and sent it to all foiling boat owners as well as the class executive. The recall notice is included at the bottom of this communication.

      The chain of events that lead to this recall are as follows:

      Two test foils broke about 6 weeks before the first delivery of foiling equipment. These breaks were of the prototype foil design, and occurred before production began. The cause was an unplanned for failure mechanism that occurs when the boat is heavily loaded to leeward and then the windward foil catches. This occurs primarily when the leaps out of the water and gets push downwind, then putting the full force of motion into the typically unloaded side of the windward board.
      These first breaks were at the inside of the elbow of the daggerboards. The foil was redesigned to account for breakage at this area, and we have not seen failure there so far.

      The boats and foils were then distributed to the first 40 teams. In the 2nd or 3rd day of sailing, the Swedish team broke on of their foils in the manner described above, but the break did not occur at the elbow as in previous iterations, instead it broke at the point of exit of the hull at the ‘bearing’ surface of the cassette that holds the board in place

      The current cassette, photographed above, is the same concept of design as used in the A-cat 4-point filing designs. It is made from an advanced plastic called POM and is a single piece. Due to it’s single piece construction, one side must be very shallow to allow the curved boards to fit though the gaps while maintaining ...
      Published on 08-03-2017 09:41 AM
      Article Preview

      Our 100′ Wally ‘Tango’ was launched in Savona, Italy yesterday to begin a busy month of sea trials before the handover to the client. This opens a new chapter in an intense and exciting build project, our largest to date. It is also ...